产品中心
ABW无功功率自动补偿控制器
ABW无功功率自动补偿控制器
产品分类:
产品简介:

本系列无功功率自动补偿控制器,应用于低压配电系统电容补偿装置的自动调节( 以下简称控制器),使用功率因数达到用户预定状态,提高电力变压器的利用效率,减少线损,改善供电的电压质量,从而提高了经济效益与社会效益。

产品详情
相关产品

功能特点 Features

1、以无功功率计算投切电容容量,补偿精度高。

2、功率因数测量精度高,显示范围宽。

3、初始相位预置( 软件调节同名或电流信号极性)。

4、具有功率因数与无功功率两种控制模式。

5、人机界面友好操作方便。

6、各种控制参数全数字可调节直观使用方便。

7、具有自动运行与手动运行两种工作方式。

8、具有过电压和欠电压保护功能。

9、具有掉电保护功能数据不丢失。

10、电流信号输入阻抗低≤ 0.01Ω。

1. Calculate the switching capacitor capacity by reactive power, and the compensation precision is high.

2. The power factor measurement accuracy is high and the display range is wide.

3. Initial phase preset (software adjusts the same name or polarity of current signal).

4. There are two control modes of power factor and reactive power.

5. The man-machine interface is friendly and easy to operate.

6. Various control parameters are fully digitally adjustable, intuitive and easy to use.

7. There are two working modes: automatic operation and manual operation.

8. With over-voltage and under-voltage protection functions.

9. With power-down protection function, data will not be lost.

10. The current signal input impedance is low ≤ 0.01Ω.


型号及其含义 Model number and it s meaning


1.jpg


产品概述 Product Overview

本系列无功功率自动补偿控制器,应用于低压配电系统电容补偿装置的自动调节( 以下简称控制器),使用功率因数达到用户预定状态,提高电力变压器的利用效率,减少线损,改善供电的电压质量,从而提高了经济效益与社会效益。

This series of reactive power automatic compensation controllers are used in the automatic adjustment of capacitance compensation devices in low-voltage power distribution systems (hereinafter referred to as controllers), using the power factor to reach the user's predetermined state, improving the utilization efficiency of power transformers, reducing line losses, and improving power supply. high voltage quality, thereby improving economic and social benefits.


正常使用条件 Normal use c onditions

◇ 海拔高度不超过2500m。

◇ 环境温度-25℃ ~+50℃。

◇ 空气湿度在40℃时不超过50%,20℃时不超过90%。

◇ 周围环境无腐蚀性气体,无导电尘埃,无易燃易爆的介质存在。

◇ 安装地点无剧烈震动。

◇ The altitude does not exceed 2500m.

◇ Ambient temperature -25℃ ~+50℃ .

◇ The air humidity should not exceed 50% at 40° C and 90% at 20° C.

◇ There is no corrosive gas, no conductive dust, and no flammable and explosive medium in the surrounding environment.

◇ There is no severe vibration at the installation site.


技术数据 Technical data

额定工作电压AC380V 50Hz

额定工作电流 AC0-5A 50Hz

额定触点容量 AC220V 7A 50Hz

显示功率因数 滞后0.001 超前0.001

测量无功功率 0-9999Kvar

欠压保护值300V

控制方式 自动寻优循环投切

灵敏度 60mA

防护等级 外壳IP40

Rated working voltage AC380V 50Hz

Rated working current AC0-5A 50Hz

Rated contact capacity AC220V 7A 50Hz

Display power factor lag 0.001 lead 0.001

Measuring reactive power 0-9999Kvar

Undervoltage protection value 300V

Control mode Automatic optimization cycle switching

Sensitivity 60mA

Protection class enclosure IP40


工作模式的特点,任何时刻控制器只能工作在1 种工作模式下

The characteristics of the working mode, the controller can only work in one working mode at any time

功率因数控制模式的特点:本控制器在出厂前已将工作模式调整在功率因数控制模式下,所有参数已按合理的方式预置,用户只要接线正确就能正常工作,无须任何操作。

无功功率控制模式的特点:能精确的控制电容器组的投切无投切震荡,适合所有工作环境特别是负载轻电容容量大的场合。

Features of power factor control mode: The controller has been adjusted to work in power factor control mode before leaving the factory, all parameters have been preset in the most reasonable way, the user can work normally without any operation as long as the wiring is correct.

Features of reactive power control mode: It can precisely control the capacitor bank without throwing oscillation, which is suitable for all working environment, especially for the occasion of light load and large capacitor capacity.


功率因数控制模式与无功功率控制模式的选择

Selec tion of power factor control mode and r eactive power control mode

控制器工作模式的选择是利用 参数的取值不同来区别的,如用户将参数调节在(1-12) 内则表示控制器工作在功率因数模式下,数据的大小表示控制器输出回路的多少,如用户将参数调节在(50-5000) 则表示控制器工作在无功功率控制模式下,数据的大小表示用户系统总电流互感器变比。

注:在无功功率控制模式下用户在没有使用控制器之前必须给控制器输入实际电流互感器变比及所有电容器容量等参数。

The working mode of the controller is selected by using different values of parameters to distinguish, such as the user will adjust the parameters within (1-12) means that the controller works in the power factor mode, the size of the data indicates how much the controller output loop, such as the user will adjust the parameters in (50-5000) means that the controller works in the reactive power control mode, the size of the data indicates the user's total system current Transformer ratio.

Note: In the reactive power control mode, the user must input the actual current transformer ratio and all capacitor capacity parameters to the controller before using the controller.


2.jpg


3.jpg


4.jpg


5.jpg


6.jpg